Макетиране и техники на макетирането | All about layouts > Похвалете се с вашия макет | Show us Your layout
Prognosis H0 model railroad - "The town from the dining room"
prognosis:
Sorry for the mistake. Because emotions and fatigue ... :yes:
prognosis:
Maintenance - interior furnishings, the couple cut short and inscriptions
http://trenulete.info/intretinere-mobilier-interior-cuple-scurtate-si-inscriptionari/
This weekend I worked a few trinkets, which, however, seem insignificant though, kidnap quite long.
First I made interior furnishings that remained indebted to Automotorul Prognosis. I want to do and an electrical coupling to power the lighting in car tow tractor wagon, so the train stops from where the tractor stops on a line segment energized, the parking lights remain lit, this time for a special note to my analog system.
Then they came for the stickers, I've written on here and there, in important respects. Priority is bonding with the inscription of the electricity, lightning warning. And for my diorama, the city is invented by me, we ought to dedicate some PanArin depot wagon, which I also made a logo and an inscription for freight cars ...
For some coaches Piko, classic axle couplings were oversized so ancient distance between tapoane was over 10 mm. Compared with other joints, all Piko and all the old generation, fixing holes were different, so ...
And in addition, we completed the collection of dedicated gondola transport trolley, with another car ... made by Gondo method for trolleybuses
prognosis:
Drill home made
http://trenulete.info/masina-de-gaurit-home-made/
How do I drill a large, 220 volt, but whose small spiral chuck can not catch, so necessary in models, I decided to use the engine PanArin stores, something old, 24-volt used in the old windshield wipers to trams, to build a drill smaller and easier to handle in models, which have not beat the strands of 1mm or thinner.
For this, I ordered a lathe chuck a reduction from an old mine, a hand drill and screw shaft of the motor. Also I did everything turned aluminum, a pressure cap on the motor shaft to adjust the pressure with a ball and a spring and there are still cool and engine lubrication
The handle is made of textolit engine and comes with strips of aluminum plate and screws. The handle I placed a starting Micro. The machine is fed through a feeder trains FZ1. Unfortunately not much jaw chuck ....
But it's important that you make yourself a mini drill Scale models.
prognosis:
The American Mehano with directional lights
Film presentation http://trenulete.info/inca-o-americana-cu-fason/
Came from a particular depot in Ploiesti, the American locomotive, product range Mehano hobby, is the U.S. sent two directional lighting installation. As we have done and first, I made holes for the red lights right in dwellings position lights imitated in the case. For that, the first was scored with a sharp needle, just the center hole where it will locate the front position. To perfect score in the middle, with a file to slightly flattened hemispherical shape of the lamp housing imitated in the locomotive. Propriuziză drilling followed the steps, spirals ever higher up the scale LED punctiform type which was to be used. Drilling in speed is necessary to keep strictly to the exact shape of the hole center lamp housing emulated.
Point red LEDs are connected in parallel and in series with a 920 ohm rzistor plate mounted above the engine. For central lighthouse we used a white neon light, a resistor in series with 820 ohms. Light is positioned so that light can be applied to both headlights stacked central and part of it be passed on plates with numbers and specific light American locomotives.
For extra effect, I placed in the cabin and a 12 volt bulb that gives a pleasant light in the cab.
prognosis:
http://www.youtube.com/watch?v=-6weMp-fuzg
Навигация
[0] Списък на темите
Премини на пълна версия