Макетиране и техники на макетирането | All about layouts > Похвалете се с вашия макет | Show us Your layout
Prognosis H0 model railroad - "The town from the dining room"
prognosis:
Chart no. Set of 20 drawings from STIPP, set the first time we presented the construction shed built since 2009.
Presented on A4 paper, the various pieces of this set are very easy to accomplish and results in much more expensive than a plastic box kitt. The process is relatively simple. I have complicated things a bit, adding the sheet of paper a more solid support, ie 1 mm thick pressboard cardboard to give an increased stability of the building. It can be done by two methods. Whether simply cutting and pasting parts of their sketch, only paper or print them on school bond, cardboard cut pressboard walls, installation of the house and then pasting the sticker. I used an intermediate approach, ie we cut pressboard walls, I cut out the design on paper and after assembling the walls, I stuck with paper prenadez model.
We started with clamps but under the roof support, as I said, stuck with the cardboard backing prenadez pressboard 1 mm thick and cut with the climb and then rip. As we proceeded with the roof plate, which I left to dry.
I went on the walls to the coal bunker, which is about 2 mm thick, used as the inner support pieces of corrugated cardboard perfume boxes (packaging), thick cardboard and proper that I pasted paper model prenadez. Bunker is a reproduction of a wooden model.
Camera magazine is executed as described above. Sure, you can cut the window as we made the draw to be mounted inside luminaa. Prodecat I did not want to fill out so that only an outdoor lighting pole, such as those made by my home and I will not put the light inside
This building presents a back wall, 3mm thick, like a protective wall and integral with the rear wall of the warehouse. We used to provide indoor (in paper), the same forex board thickness, polished to catch prenadezul, on which I glued and folded paper by the same process model as described in the introduction.
Platform to support the magazine, was made by gluing all paper model hard pressboard, which I mounted the box walls and rear wall with coal bunker, after which I added to strengthen the roof and clamps above.
As we proceeded with the pillar of support and diesel pump, but worked directly from the paper. I do not recommend the use of polyvinyl acetate because the paper absorbs moisture model and curls. I worked two such shops, one of the original paper, copied from a Xerox color (laser) on the school bond. This process is simpler for use prenadezului remove, but it requires attention to fixing any further niscare not allowed. prenadezul let you move but a few minutes adjusting the correct position paper printed decoration.
It follows that after drying and curing, to do the finishing touches to creoiane colored pens or paper where the combination is too obvious, adding exterior lights and a white LED lighting pole-warm, decorate with flowers or ivy and arba, aging and dirt here and there, in important respects.
It follows a simple but beautiful work for modelers unpretentious, it appears that no relief from joining hollow bricks, but quite pleasant to the viewer. A simple layout and easy to do, the time being about 2-3 hours of work.
The set of plans includes several buildings that you try to accomplish in coming days and I will present after completion. Who needs these models can contact me!
http://trenulete.info/cladirea-loktankstelle-de-la-stipp/
prognosis:
I continued this work, first making charcoal from wood bunker. I used a piece of pulp with coarse as to resemble pieces of coal, cut the size of the bunker interior painted matt black and REVELL.
After installation, I used a stick to clean ears, soaked in paint thinner and paint the areas that I stretched to reach. We spread the misery as artistically ... on corners, on walls in the neighborhood, the roof, columns and floors.
Using colors I vacsuit edges cuts close to the roof and walls so as to give a touch of old and dirty.
Unfortunately, so have problems with images not currently make only one picture here. The rest can be seen here:
http://trenulete.info/cladirea-loktankstelle-de-la-stipp/ I apologize for sending board members.
Vlado:
:clapping: :clapping: :clapping: Good job!!!
prognosis:
Cladirea Spritzenhaus de la Auhagen Stipp http://trenulete.info/cladirea-spritzenhaus-de-la-auhagen-stipp/
Another construction paper, all Stipp Auhagen the set is Spritzenhaus magazine (ie, where the Germans are going to drink on lunch break :on_the_quiet: ...)
Using the same methods as Loktankstelle building, I realized two fitting parts, the warehouse itself and covered shed next to her. I started to shed, whose walls I lined 2mm thick pressboard. To bend the edges correctly, we used plastic boxes from sidewalks, on whose edges have decorative paper bent elbow.
To store, we doubled the pressboard walls 1 mm thick, cut as the design of a building inside which I did, I stuck to the walls of paper.
Mounting cardboard walls was easier if I used the original attachment, self-adhesive paper that is used in the application of prices on various products to stores, which for the time set apart walls.
I lined the interior walls of the school bond cream, to give shade painted wall and floor I used all school bond gray. We cut doors bulge to make them functional. Doors are made separately so that they open. Instead we used a gummed hinge stuck between decorative surface. Edges with the color we painted the door. Inside, the two decorative layers, we placed a piece of cardboard cards to strengthen the door surface.
At present, the collection Auhagen, I have worked on these buildings.
the remaining station buildings and office administration to move the depot, which realize them-meaning the next few days. Finally, all these new buildings will decorate mini-diorama piece, which will be connected to the diorama's Prognosis, a small part of the depot will be 3-4 times, revolving plate and other accessories, all made in home made style, paper and forex. In parallel work on board and automotorul revolving mixer.
prognosis:
Stipp Auhagen Briescht the building - no body. 1
http://trenulete.info/cladirea-briescht-de-la-auhagen-stipp/
Depot buildings set to continue Auhagen Briescht combination of no board I worked today. 1, corresponding to the largest building in the last grouping, which represents the station, stores and office moving freight and parcels.
Chart no. 1, the station's main building, is the central part, which binds all other bodies, was first on the list naturally.
In this building we decided to cut out windows and mounting them in relief, so that building can be equipped with interior lighting. To this must be cut to window frames climb on board printed
Then, the two sides of the walls of the sample mounts after all edges have been bent at odds.
The 1 mm thick pressboard, cut replicates the walls and windows and doors are cut so that light can pass from inteior. Drawing is done by aligning the correct model of pressboard cut piece printed with pencil and tracing decupaturilor circumference so that they overlap perfectly fitting.
Duplicates for mounting on walls, taking care to match deculajele well, stick with the model prenadez printed on the back and make sure you have tape on the seam position until stiff. Follow clippings shaping interiors with soft brush and a color as close to the printed pattern. I gave a pale brown brick.
Follow cutting and pasting their backup windows as centered within the building, each in the right place so unacceptable to see any light through the windows and the model to gain depth in their right.
After a first test of flatness and fixing windows and joints following minor changes to the mail box manufacturing. I have also added outside the window sills, which we painted a suitable color.
Meanwhile, sticks, cardboard, pressboard dubbed the roof and let it dry.
After drying, I painted the roof with gray bottom, in areas where we can see from the outside underneath. After drying I glued to the roof and I pressed the correct position better because light can not penetrate the bond among the edges. For safety, stick adhesive paper inside is dark for the entire length of the joints.
Finally I made of 3 mm thickness and forex steps to the side door. No follow making body. 2. Finally, chimneys will be installed and will add vegetation and lighting.
Навигация
[0] Списък на темите
Премини на пълна версия