Макетиране и техники на макетирането | All about layouts > Похвалете се с вашия макет | Show us Your layout
Prognosis H0 model railroad - "The town from the dining room"
prognosis:
http://observator.a1.ro/social/Orasul-din-sufragerie_32166.html
http://videonews.antena3.ro/action/viewvideo/71971/Blumemberg-orAAaaAzelul-din-sufrageria-unui-romaEn-pasionat-de-construcaatii/
n_sirakov:
:clapping: :clapping: :hi:
prognosis:
Thanks dear friends!
http://trenulete.info/orasul-din-sufragerie-la-antene/
prognosis:
Cls passenger wagon. Series I 51 53 19 - Lighting
http://trenulete.info/vagonul-de-calatori-cls-i-seria-51-53-19-iluminare/
Lighting arrived in Botosani, two Romanian coaches at the depot today entered Tilligh PanArin for interventions. First, grade wagon. I received my home riglete made with white SMD LEDs, one for each compartment, or 9 pieces. LEDs are mounted in parallel to operate both analog and digital in, knowing that the series, the light is only slightly higher voltage, which is quite annoying in analog.
LEDs are serially connected with a 820 ohm resistor and an electrolytic capacitor using micro/25volti 1000, in parallel, remove palpaielile caused by interrupted supply or dirty self. Recovery was made with four diodes 1n4001 and blood collection were placed on slides using specialized sites. The thread passes through the middle bogie axle and axle plate acts both cars.
prognosis:
Cls passenger wagon. Series II 51 53 20 - Lighting
http://trenulete.info/vagonul-de-calatori-cls-ii-seria-51-53-20-% E2% 80% 93-lighting /
What is the second coach from Tillig Romanian, Series 51 53, he received enlightenment in all departments, plus the final lamp at one end.
For lamps end, the intervention was somewhat more difficult because of construction, the wagon was not equipped with prisms (light guides) and that the holes in the frame lights, which lowers the note manufacturer for negligence. Drilling procedure must be executed with great precision, in steps, starting with very small spiral (0.5) and continuing up to the maximum permitted frame diameter reflector. It is very important that the initial alignment for the first hole, to be made in principle, very carefully, and using a needle under a microscope for scoring. It is also important that the drill be quality, without batting in madrina (... which does not possess, but pierce the hand, throwing the first spiral in a spiral trap, which rotate at hand, my car Drill is one that do not allow such a thing) ... Because of the wagon body molding material is white, slightly transparent, the inside wall, right headlight, and I applied paint negra Revell have also done inside the frame headlamp.
I used two lamps for the final SMD LED, in series between them and then in series with a resistor of 1.2 k For stability, they call a capacitor coupled in parallel with the 1000micro/25 volts. SMD's are soldered directly onto the wagon chassis, right headlight charged holes. Because I did not hole the size of transparent prisms, headlight lens is made of glue ... Revell, poured carefully into those holes, I glued back after temporary waxed paper tape. After drying and hardening the adhesive, the lights have got a touch of realism. I think that is better suited to the manufacture of molded lenses, the material used in water to emulate the scale models.
On rigleta lighting, we separated immediately after leaving the bridge rectifier, two routes, one for lighting compartments, one for lamps and final. At each have stabilized the same light with one capacitor mounted beside each toilet cubicles. All rigleta is one piece, removable, no seams in contact with the wagon, so that any intervention should take place without much effort. To illuminate the compartments were used neon white SMD LEDs, in parallel with each other and in series with a resistor of 820 ohms, so that the illumination parameters fuctioneze in both analog and in digital.
Навигация
[0] Списък на темите
Премини на пълна версия